News

Hello, come to consult our products !
  • Attention rules for injection mold design

    1. Mold opening direction and parting line Each injection product must first determine its mold opening direction and parting line at the beginning of the design to ensure that the core-pulling slider mechanism is minimized and the effect of the parting line on the appearance is eliminated. 1) Af...
    Read more
  • The development history of home appliance mould

    In the early stage of reform and opening up, household appliances carried people’s yearning for a better life, and were one of the important signs of the family’s material living standards. In the past 40 years of reform and opening up, the development of the household appliance manufacturing ind...
    Read more
  • Mold parts processing technology

    In order to ensure the rationality and consistency of the mold making and processing technology, optimize the processing technology, and improve the progress of the mold making, each mold factory generally formulates the process standards suitable for the factory. 1. The craftsperson compiles cra...
    Read more
  • The process from mold design to mold trial (part 2)

    In the last article, we talked about the part1 part of the mold design to the trial mold process, and then we will continue to explain it to you. 2. Proofreading, reviewing, tracing, and sending photos (1) The relationship between the mold and its parts and the drawing of the plastic part Whether...
    Read more
  • Explanation of the process from mold design to mold trial

    Draw mold diagram    Before drawing the mold assembly drawing, the process drawing should be drawn, and it should meet the requirements of the part drawing and process data. The size guaranteed by the next process should be marked with the words “process size” on the drawing. If aft...
    Read more
  • Top Ten Problems of Mold Trial

    Common problems in mold trial 1: The main runner sticks to the mold The method and order of solving the problem: 1 Polishing the main runner → 2 nozzles coincide with the center of the mold → 3 lowering the mold temperature → 4 shortening the injection time → 5 increasing the cooling time → 6 che...
    Read more
  • How does the “burr” of the injection mold occur?

    Injection molding products refer to plastics that are heated, plasticized and melted by an injection molding machine, and then injected into the cavity of a molding mold for molding. After cooling down, the melt is solidified and demolded, and the injection molding machine is injection molded. Fl...
    Read more
  • The 5 effects of mold temperature on the quality control of injection molded parts

    1. The influence of mold temperature on product appearance Higher temperature can improve the fluidity of the resin, which usually makes the surface of the part smooth and shiny, especially to improve the surface beauty of glass fiber reinforced resin parts. It also improves the strength and appe...
    Read more
  • Talking about the 5 effects of mold temperature on the quality control of injection molded parts

    1. The influence of mold temperature on product appearance Higher temperature can improve the fluidity of the resin, which usually makes the surface of the part smooth and shiny, especially to improve the surface beauty of glass fiber reinforced resin parts. It also improves the strength and appe...
    Read more
  • Selection and installation of injection mold pressure sensor

    The pressure sensor can be installed in the nozzle of the injection molding machine, the hot runner system, the cold runner system and the cavity of the mold. It can measure the plastic from the injection molding machine nozzle to the Plastic pressure somewhere between the mold cavities. This dat...
    Read more
  • Analysis of the problems and causes of the injection mold!

    The deformation, bending and twisting of deformed products are mainly due to the fact that the shrinkage rate in the flow direction is larger than that in the vertical direction during plastic molding, which causes the parts to be warped due to different shrinkage rates in each direction. It is a...
    Read more
  • Analysis of the problems and causes of injection molds!

    Analysis of Causes of Cracking of Injection Molded Products Cracking, including surface filiform cracks, micro-cracks, whitening, cracking, and the risk of trauma caused by the sticking of parts and runners, according to the cracking time, it is divided into demoulding cracking and application cr...
    Read more